quilted potholders free pattern

'You're-my-cupcake' quilted pot-holders:

29/11/2020

A design collab with Riley Blake Designs - 'From the heart' fabric collection by Sandy Gervais

'YOU'RE-MY-CUPCAKE' pot-holders

Everybody needs pot-holders in the kitchen, and if they're this cute, even better, right?
So how about pulling out some fabric and getting started.
These are super easy to make and will be a perfect gift for any passionate cook.

'YOU'RE-MY-CUPCAKE' pot-holders

'You-are-my-cupcake' pot-holders
finished size 8"x 10"

Fabrics needed per pot-holder:

- finished cupcake quilt block 8"x 8"
- cut 2 pieces of fabric for backing 8 1/2"x 10 1/2"
- cut 1 piece of fabric 8 1/2"x 8 1/2" for pocket lining
- 1 piece of fusible interfacing 8 1/2"x 8 1/2" for pocket
- 1 piece of fusible interfacing 8 1/2"x 10 1/2" for backing
- 1 piece of insul-brite 8 1/2"x 10 1/2" for backing
- cut 1 strip of fabric 1 1/2"x 10" as binding for pocket
- cut 1 strip of fabric 2"x 6" or use ribbon for hanging tab
- bias tape 2"x 40" for pot-holder binding

Sewing the potholder:
1. Finish the cup cake quilt block ( shop pattern here ) in size 8"x 8"
2. Cut all of your fabric pieces as mentioned above.

finished cupcake quilt block

3. Iron on fusible interfacing to your quilt block .
Then lay pocket lining piece of fabric face down on flat surface and lay quilt block face up on top of it. Clip or pin in place.
4. Quilt as desired, to hold these layers together.
I did 1" diagonal squares. I used my acrylic ruler and a fabric chalk pen to draw the lines.

Drawing the lines with a fabric chalk pen

5. Trim to 8"x 8" size.

quilted and trimmed pocket piece

6. Iron on the fusible interfacing to one of the backing fabrics.
Place the other backing fabric face down on a flat surface. Position the insul-brite on top of it and finish off with the backing/fusable interfacing piece, face up.
Pin or clip all three layers in place.
Quilt as desired, I did 1" diagonal squares again, as with the pocket piece.

Make the hanging tab: ( or use a strip of ribbon)
- Fold the 2"x 6" strip in half lengthwise and press. Fold in 1/4" seam allowance on each long raw edge and press again.
- Stitch with small seam allowance.
- Fold the tab in half and clip in place at the center of the back of your pot-holder.

attach hanging tab at the center

7. Binding for the pocket:
Take the strip of fabric 1 1/2"x 10" and pin it to the top of the cupcake pocket with the raw edges aligned and stitch in place with 1/4" seam allowance. ( photo 1)
Fold the binding over to the back ( photo 2) and stitch in place ( photo 3)
Finished binding seen from the front ( photo 4)
Trim the ends.

binding for pocket

fold over binding to the back

stitch binding in palce

binding from the front

8. Place the quilted pocket piece on top of the backing ,
aligning the side and the bottom raw edges. Clip or pin in place.

9. Round the corners of your pot-holder.
I drew a 1/4 circle at the corners first and then cut it.
here's a template for the corners, cut it along the black line.

draw your round corners

rounded corners

10. Fold the bias tape over 1/4" at one end of the binding strip and clip or pin in place around the pot-holder with the end overlapping about 1/2" ( photo 1 ) .
Stitch in place. ( photo 2 ).
Fold the binding over to the backof the pot-holder and then hand stitch in place.

attach bias tape

stitch bias tape in place

fold tape over to the back

Et voila .... all done.

'be-my-cupcake' pot-holder

Thank you so much to Riley Blake Designs for supplying the absolutely adorable
'From the Heart' fabric series designed by Sandy Gervais that I used
in this super cute project.